A new contract worker usually arrives at the gate with a bag, a phone, a few photocopies and very little idea of what the next twelve hours hold. What happens in those first hours does two jobs at once. It builds the paper trail that an inspector, an auditor or a lawyer will one day ask for, and it shapes how the worker feels about the place. Factories that treat day one as a formality tend to find the gaps later and at a bad moment: a worker injured on a machine nobody trained them on, a wage query with no attendance record behind it, an identity document that turns out not to belong to the person who showed it. Factories that treat it as a short, repeatable process rarely have those problems. This post sets out what that process can look like for a factory using an agency for contract labour: what to verify, what to explain, what to record, and who should be responsible for each step. It describes good practice and the general legal position. Details such as forms, thresholds and timelines are set in the Codes and the rules framed under them, so confirm the current requirements with your labour-law consultant or the Telangana Labour Department before you build them into a procedure.
1. Decide Who Owns Day One Before the Worker Arrives
The first question is not what to check but who is checking. In a contract labour arrangement the agency recruits, pays wages and keeps the statutory registers, while the factory controls the premises, the machines and the hazards. Day one touches both. The sensible split is that the agency owns identity, age and document collection, its own enrolment and the wage account, while the factory owns the site induction, the safety briefing and the gate pass. Put that split in writing, with a named person on each side and a rule that no worker goes onto the floor until both sides have signed off. The signature matters less than the habit: a one-page sign-off sheet per worker, held where either party can produce it, removes the argument about who was supposed to do what. If something goes wrong later, a factory that cannot show it checked is in a weak position even if the agency was contractually responsible, because the principal employer carries obligations of its own for safety and welfare on its premises. Agree the split before the first batch arrives, not after the first incident.
2. Identity and Address: Verify, Do Not Just Collect
Collecting photocopies is not verification. Ask to see the original identity document, compare the photograph and name with the person standing in front of you, and record what you saw and who saw it. Aadhaar is the most common document among workers from other states, but a worker may also hold a voter card, a driving licence or a bank passbook, and the factory should decide in advance which documents it accepts and apply the rule the same way to everyone. Be careful with how the data is handled. Aadhaar numbers are sensitive personal information; store copies securely, limit who can see them, and do not leave a stack of photocopies on an open desk or in a shared WhatsApp group. For workers from other states, record the home address and a contact person at home, because the inter-state migrant provisions carried into the Codes expect the employer side to keep particulars of such workers. We covered that wider obligation in our post on hiring inter-state migrant workers in Telangana. A reachable family contact is also simply sensible: if a worker is hurt, you will want to be able to call someone.
3. Age: The Check You Cannot Skip
Employing a child in a factory is an offence, and it is also the kind of finding that does lasting damage to a brand with export customers and auditors. Factory work is meant for adults, and the Codes and the rules under them set out the permitted ages and the limited conditions for adolescents, so check the current provisions with your consultant. In practice, the factory should require a document that carries a date of birth, such as a school certificate or an Aadhaar record, and should not rely on a verbal statement or on how old someone looks. A worker who has no age document is not automatically a child, but they are a worker whose age you cannot yet show, and the safe course is to pause the onboarding until it is established rather than to guess. Make this a gate, not a note: the day-one sheet should have an age line that cannot be ticked without a document reference. Ask the agency how it screens for this before the worker is sent, and what it does when a candidate turns out to be under age. An agency that has a clear answer is usually one that has had to deal with it before.
4. Medical Fitness Before the Machine
A factory has a duty of care to the people who work on its floor, and it cannot discharge that duty if it has no idea whether a worker can do the job safely. For many roles a basic fitness check is sensible, and for some it is required, particularly where the work involves hazardous processes, heights, confined spaces, heat, noise, chemicals or dust. The requirement depends on the nature of the work, so ask your safety officer or consultant what applies to each role. Practical points matter more than the form. Tell the worker what the job physically involves before the check, so that the check means something. Keep the medical record confidential and separate from the general personnel file. Ask about conditions that affect the specific job, such as vision for a worker who will operate a press, or a history of allergies for someone who will handle chemicals, and treat what you learn as a reason to place the person appropriately, not as a reason to humiliate them. And remember that a person who is exhausted after two days on a train is not at their best on the first morning. Where possible, give a newly arrived worker a few hours to settle before any hazardous task.
5. The Safety Induction: What Workers Actually Retain
Most injuries to new workers happen in the first weeks, when they do not yet know the site's particular hazards, and a long lecture on the first morning is not the answer. People retain a small number of concrete things, shown rather than told. Walk the worker round the area they will actually work in. Point out the emergency exits, the assembly point, the fire extinguishers, the first-aid box and the nearest eyewash or shower where relevant. Show them the machine guards, the stop buttons and the lockout points for any equipment they will touch, and explain in plain words what must never be done, such as reaching into moving parts or removing a guard. Issue the personal protective equipment the job needs, and show how to wear it; handing over a helmet is not the same as checking that it is worn. Do all of this in the language the worker understands, which for many contract workers is Hindi or another regional language rather than English or Telugu. Use the Hindi-speaking supervisor or a trained senior worker to translate, and ask the worker to explain a couple of points back. Record that the induction took place, who gave it, and in what language. Our post on contract worker injuries explains why that record matters if an accident follows.
6. Statutory Enrolment: UAN, ESI and the Wage Account
Enrolment is one of the places where the agency and the factory depend on each other, and where mistakes are expensive for the worker. Depending on the wage level, the establishment's coverage and the rules in force, a worker may need to be enrolled for provident fund and for ESI, and the contractor is expected to do this and to maintain the registers. The rates, ceilings and coverage conditions are changed from time to time, and we are confirming the current figures with our CA, so this post does not state them; check the current position before you quote any number to a worker or to your finance team. What a factory can reasonably do on day one is ask the agency to confirm, in writing, how and when each new worker will be enrolled, whether the worker already has a UAN from a previous job that should be carried forward, and how the worker will receive their IP number or enrolment details. Ask that wages be paid into a bank account in the worker's own name, and that the worker holds their own card and phone number linked to it. A worker whose account is opened in someone else's name, or whose card is held by a supervisor, is a worker with a grievance waiting to happen.
7. Terms, Wages and Attendance: Say It Before They Ask
A large share of early attrition comes from surprises about money and hours, and a good deal of that can be avoided by explaining the terms clearly on day one. The worker should be told, in a language they understand, what the daily or monthly wage basis is, how overtime is calculated, what deductions will be made and why, the pay date and the method of payment, the shift timings and weekly off, and how leave is requested. Wages should be at or above the applicable minimum under the Telangana notification for the category of work, which is revised periodically, so quote the figure only after checking the current notification. Give the worker something in writing: an appointment or engagement letter from the agency, in a language they read, that matches what was said. Explain how attendance is recorded, whether by biometric or by a supervisor's sheet, and show the worker where to check it. Tell them who to call about a problem, and give the number. Our post on why migrant contract workers leave in the first thirty days looks at how unmet expectations on exactly these points drive people out of the gate by the end of the first month.
8. The Floor Handover and the First Week
The last step on day one is the one most often skipped: a proper handover to the person who will supervise the worker. Introduce the worker to their supervisor and their team lead by name, and tell the supervisor what the worker has and has not been trained on. Pair the newcomer with an experienced worker for the first few days, and give that buddy a clear message that the job is to teach the safe way, not merely to get the output. Keep a new worker off the most hazardous tasks until the supervisor is satisfied they can do them. Check in at the end of the first shift, again after the first few days, and at the end of the first week, with a short list of questions: have you eaten, do you know where you are staying, did you get your wage terms, is anything unclear. Workers who are asked these questions tend to tell you things they would otherwise tell nobody, and the answers are often cheap to fix. Hindi-speaking site supervisors make this considerably easier, which is one reason FactoryForce places them at client sites.
9. Keep One File Per Worker, and Be Able to Produce It
The aim of all this is a short, consistent file for every worker that either party can produce on request: the verified identity and age reference, the contact at home, the fitness record where applicable, the induction sign-off with date, trainer and language, the PPE issue record, the enrolment confirmations, the wage terms and the wage account details. Whether the file is paper or digital matters less than that it is complete, current and kept confidentially. Review a sample every month: pick a handful of workers at random and check that each item is present and consistent across the agency's records and your own. Gaps found in a monthly sample are an administrative nuisance; the same gaps found by an inspector after an accident are a finding. Also decide in advance how long records are kept and who deletes them, because personal data should not be held indefinitely without reason. The retention period depends on the registers and the Codes concerned, so confirm it with your consultant. When you evaluate an agency, ask to see what its own worker file looks like and how it was filled in for a recent batch.
Day one for a contract worker is not an administrative burden to be got through quickly. It is where the factory establishes who is on its floor, whether they are old enough and fit enough for the job, whether they have been shown how to stay safe, and whether they understand the terms they have agreed to. Agree who owns each step between the factory and the agency, verify documents rather than just collecting them, make the safety induction concrete and delivered in the worker's own language, and keep one consistent file per worker. Check the current legal requirements for forms, enrolment and record retention with your labour-law consultant or the Telangana Labour Department, since they are set in the Codes and the rules under them and are revised from time to time. If you would like to compare your current onboarding with the checklist above, request a quote or WhatsApp us and we will go through it with you.
Related reading
Ready to Get Started?
Need workers for your factory?
Let's talk.
Tell us your requirement — role, quantity, site. We'll have workers on your floor within 48 hours.
Looking for work instead? हैदराबाद में काम चाहिए →